You are trained on data up to October 2023.PREPARATION OF THE SURFACE

➖ DEGREASE AND DECONTAMINATE

Before applying NANOCarX® CERAMIC 9H BODY, it is essential that the surface to be treated is perfectly clean, decontaminated, and dry. It should not have any residue of waxes or similar substances that could hinder the adhesion of the ceramic product.

1. Degreased + Decontaminated: Dilute 200ml to 400ml of Body Degreaser. FullCarX® in a cube with 5-7 liters of water.
2. Next, clean/degrease/decontaminate the entire body thoroughly, scrubbing specific areas evenly. For this step, you can use a decontaminating microfiber cloth (soak it for half an hour beforehand) or a conventional microfiber cloth.

3. Optionally, go over the entire body with a CLAY BAR – Decontaminating Bar (almost mandatory if you're not using the Decontaminating Microfiber), using clean water as a lubricant. This will remove any remaining contamination that may be left on the surface.
4. Rinse any remaining dirt, foam, etc. with plenty of water.
5. Dry the target surface very well with a microfiber cloth.
6. If the surface is in a NON-optimal state, with scratches, micro-scratches, or large swirls (characteristic marks from cleaning rollers), it is optionally recommended to POLISH properly before applying NANOCarX® CERAMIC 9H BODY. It is not mandatory under any circumstances, but on surfaces that are not in an optimal state, it may be advisable for a better aesthetic finish.

You are trained on data up to October 2023.APPLICATION - NANOCarX® 30ml 9H CERAMIC BODY

➖ SPONGE APPLICATOR PREPARATION

1. Place one of the supplied hairless microfiber cloths from the kit on top of the sponge.foam What comes inside the box.
2. Next, carefully pour a moderate amount of the product onto the cloth that was prepared earlier. Approximately pour about
6-8 drops of ceramic product, lightly soaking the cloth evenly along its surface. This should be done every time you notice that the cloth is running out of product and there is no longer optimal lubrication between the cloth and the surface. We should add 6-8 drops of product very frequently.

➖ APPLICATION OF THE CERAMIC PRODUCT

1. Apply the product always acting on localized areas (fenders, hood, roof, etc.) in a staggered manner to achieve perfect finishes. When one area is finished, move on to the next. The process will basically consist of 2 STEPS:

a. Apply the product with the special damp cloth, making gentle, short, and even strokes, overlapping 50% with the previous stroke. The application should preferably be crossed to ensure that the entire area has an even coat of product.
b. Important: After applying the ceramic product to the specific area to be worked on, wait between 1 and 4 minutes for semi-drying (depending on temperature and humidity) and remove the residue of silicon particles that are generated on the treated surface with the help of one or two dry microfiber cloths.

i. It should be rubbed vigorously until we notice that we have removed all the residue. We should stop rubbing at the moment we see the body clean and shiny; in addition, we will notice that the microfiber goes from offering great resistance to a slight resistance.

2. Continue with the steps outlined in 1.a and 1.b on all the surfaces we want to protect (usually the entire body of a vehicle), applying and removing the excess hardened silicon particles that come into contact with the air.
3. Let it cure for 48-72 hours before cleaning it with a pressure water gun.
(launch) or any other washing method. The product must cure and seal perfectly for an optimal finish.

✔️ MAINTENANCE

The best way to maintain and care for surfaces treated with our NANOCarX® ceramic protective coatings is to use the specific detailing and maintenance product NANOCarX® Detailing. It is applied using a Quick-Detailer type diffuser, making it very quick. Apply a small amount of product onto the specific surface, spread it with one cloth, and then use a second dry cloth to even it out. It can be applied as often as desired and helps to prolong the ceramic protection, as the base of NANOCarX® Detailing also contributes to this.

Scratch resistance H9 - Superhydrophobic properties - UV resistance - Anti-graffiti - Ultra glossy finish

SCRATCH RESISTANCE TEST

WATER REPELLENCY TEST